Evolution RAGE3S3002 Manual de Instruções

TCT Multipurpose Sliding Mitre Saw Range ManualOriginal Instruction ManualRead instructions before operating toolsModels manual is applicable to:RAGE3

10www.evolutionpowertools.comand that comply with the requirements of EN 847-1Do Not use saw blades that are damaged or deformed as they could shatter

11www.evolutionpowertools.comglasses with side shield or a full face shield when needed. WARNING: If any parts are missing, do not operate your mitre

12www.evolutionpowertools.comADDITIONAL ACCESSORIESIn addition to the standard items supplied with this machine, other accessories are available to en

13www.evolutionpowertools.comOVERALL VIEW OF MITER SAW 1. ON/OFF TRIGGER SWITCH 2. BLADE GUARD LOCKING TRIGGER 3. CUTTING HANDLE 4. DUST BAG (Optiona

14www.evolutionpowertools.comASSEMBLY AND PREPARATIONWARNING: Always disconnect the saw from the power source before making any adjustments.NOTE: It i

15www.evolutionpowertools.comHOLD DOWN CLAMP (Fig. 4)Two sockets (one either side) are incorporated into the rear of the machines fence. These sockets

16www.evolutionpowertools.comLASER ADJUSTMENTWARNING: At no time during this procedure should the motor be started.To check laser alignment: • Place

17www.evolutionpowertools.comNOTE: The following WARNING labels may be found on this machine: LASER RADIATION DO NOT STARE INTO THE BEAM CLASS 2 LASER

18www.evolutionpowertools.comDEPTH STOP (Fig. 8)Use of the depth stop allows the operator to cut slots in the workpiece. The downward travel of the Cu

19www.evolutionpowertools.comOPERATING INSTRUCTIONSCAUTION: The Mitre Saw should be inspected (particularly for the correct functioning of the safety

2www.evolutionpowertools.comModel SpecificationsEvolution Power Tools reserves the right to make improvements and modifications to the design and techni

20www.evolutionpowertools.comBEVEL ANGLES (00 AND 450)00 Bevel Stop Adjustment• Ensure that the Cutting Head is in the locked down position with the

21www.evolutionpowertools.com• Return the Cutting Head to its upright position.• Loosen the locknut on the 450 Bevel Adjustment Screw.• Use a Hex K

22www.evolutionpowertools.comPREPARING TO MAKE A CUTDO NOT OVER-REACHKeep good footing and balance. Stand to one side so that your face and body are o

23www.evolutionpowertools.comTHE MOTOR ON/OFF SWITCH (Fig. 19)The ON/OFF Motor Trigger Switch is a non-latching type. It is the upper of the two switc

24www.evolutionpowertools.comSLIDE CUTTINGThis saw is equipped with a Sliding Carriage system.Loosening the slide lock screw will release the slide an

25www.evolutionpowertools.comMITRE CUTTING (Fig. 27)The rotary table of this machine can be turned through 450 to the left or right from the normal cr

26www.evolutionpowertools.comTo reposition:• Lift up the lever and turn to a convenient position Release the lever• Stand to the left side of the ha

27www.evolutionpowertools.comCUTTING BOWED MATERIAL (Fig. 34)Before cutting any workpiece, check to see if it is bowed. If it is bowed the workpiece m

28www.evolutionpowertools.comFig. 38View of (1) Arbor screw, (2) Washer, (3) Blade flange, (4) Blade• Press the black arbor lock button to lock the ar

29www.evolutionpowertools.comUSE OF OPTIONAL EVOLUTION ACCESSORIES Not supplied as original equipment. All accesories can be purchased from Evolution

3www.evolutionpowertools.comRAGE3-S300 210mm TCT MULTIPURPOSE SLIDING MITRE SAW WITH 300mm SLIDEDESIGNED TO CUTMild Steel Plate – Max Thickness (mm)

30www.evolutionpowertools.comNOTE: Approximately 75mm of the Workpiece Support Bar should slide into the base to provide positive location.• Tighten

31www.evolutionpowertools.comFINAL SAFETY CHECKS FOR SELF-ASSEMBLED MACHINES ONLY All the Yes Boxes must be ticked before the machine

32www.evolutionpowertools.comMAINTENANCENOTE: Any maintenance must be carried out with the machine switched off and disconnected from the mains/batter

33www.evolutionpowertools.comYOUR NOTES

34www.evolutionpowertools.com PARTS DIAGRAM (NON ASSEMBLY)

35www.evolutionpowertools.comEC DECLARATION OF CONFORMITYIn accordance with EN ISO 17050-1:2004The manufacturer of the product covered by this Declara

36www.evolutionpowertools.com PARTS DIAGRAM (NON ASSEMBLY)

37www.evolutionpowertools.comEC DECLARATION OF CONFORMITYIn accordance with EN ISO 17050-1:2004The manufacturer of the product covered by this Declara

38www.evolutionpowertools.com PARTS DIAGRAM (NON ASSEMBLY)

39www.evolutionpowertools.comEC DECLARATION OF CONFORMITYIn accordance with EN ISO 17050-1:2004The manufacturer of the product covered by this Declara

4www.evolutionpowertools.comTABLE OF CONTENTS PAGEMachine Specification 2 - 3Introduction 5Guarantee

UK HQEvolution Power Tools, Venture One, Longacre Close, Holbrook Industrial Estate, Sheffield, S20 3FR, UKTEL: +44 (0) 114 251 1022FAX: +44 (0) 114 24

5www.evolutionpowertools.comINTRODUCTIONCongratulations on your purchase of an Evolution Power Tools machine. This product has been manufactured to th

6www.evolutionpowertools.comVIBRATION WARNING: When using this machine the operator can be exposed to high levels of vibration transmitted to the hand

7www.evolutionpowertools.comWhen fitted with a correct blade this machine can be used to cut:WoodWood derived products (MDF, Chipboard, Plywood, Blockb

8www.evolutionpowertools.comIf an extension cable is required it must be a suitable type for use outdoors and so labelled.The manufacturers instructio

9www.evolutionpowertools.comclothing or jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewellery or long hair c